This technique works for all standard single-coil pickups, including Fender’s template design, so dive in!

It’s not difficult to replace the wiring in your pickups, but it takes some finesse. Here’s a step-by-step guide.

Hello and welcome back to Mod Garage. After numerous requests, this month we’ll have a closer look at changing wires on a single-coil pickup. As our guinea pig for this, I chose a standard Stratocaster single-coil, but it’s basically the same on all single-coil pickups and easy to transfer. It’s not complicated but it is a delicate task to not destroy your pickup during this process, and there are some things you should keep in mind.

Why would you change wires on a pickup? Here’s a list of reasons I mostly hear in the shop when someone brings in a pickup for this operation:

This can happen if the wire was bent too much, or it was damaged with a soldering iron, a screw split it, etc.

Maybe one of the pre-owners snipped it out of the circuit at some point, rather than desoldering it to save the full wire length. The quick-and-dirty solution in such a case will be to extend the wire by soldering another piece of wire to it. For the “Trekkies” of us, that’s the way James T. Kirk and Scotty would fix it. Jean-Luc Picard and Geordi La Forge would solder a new wire with the correct length to the pickup to replace the old one. Make it so!

Often cheap pickups have thin and shoddy plastic-coated wires that will likely break soon. It’s always a good investment regarding reliability and longevity to swap them with a good quality wire.

Changing the wire material can alter the sound of a pickup, so replacing a cheap plastic-coated wire with a good-quality cloth-covered wire will not only look more vintage but will also result in a slightly warmer tone. Or the other way around for a slightly brighter tone. Or maybe you want to upgrade your pickups with a high-quality Teflon-coated or audiophile HiFi-wire. Perhaps you like to have neon green and pink wires on your pickups, for whatever reason.

This often goes hand in hand with shielding the complete single-coil pickup and is a logical step in such cases.

Often vintage pickups are modded with a non-original wire, sometimes as part of a repair. Bringing them back to factory specs is a good investment to keep the value of a vintage pickup alive.

So, you see there are some good reasons to change the wires on a pickup. This list is not complete; for sure there are others.

Now, let’s start our project by preparing the pickup for this operation. It’s first and foremost important to protect the windings of your pickup against any damage. It only takes a fraction of a second to hit the winding with the tip of the soldering iron and this is a scenario you do not want.

Courtesy of SINGLECOIL (www.singlecoil.com)

1. I simply put a standard plastic pickup cover on the pickup to protect the winding. I usually use two small zip ties to fasten the cover, but you can also use two small screws and a hex nut, a rubber band, or a piece of masking tape.

Courtesy of SINGLECOIL (www.singlecoil.com)

2. Have a look where the hot (usually white, yellow, or red) and the ground (usually black) wires are connected to the pickup and mark one of them. I always mark the hot connection by using a Sharpie, but you can also use a drop of nail polish, a small piece of masking tape ... be creative.

Courtesy of SINGLECOIL (www.singlecoil.com)

3. Measure the DCR (direct current resistance) of your pickup as a reference using your DMM (digital multimeter) and note it. After this is done, push the wires you want to replace upwards through the hole and pull them out, as shown in Photo 1, Photo 2, and Photo 3.

Courtesy of SINGLECOIL (www.singlecoil.com)

Now put the prepared pickup into a small vise and orient it so that you can look at the soldering terminals the two wires are connected to (Photo 4). Take care to not apply too much pressure with the vise: We only want to fasten the pickup, not break it.

Courtesy of SINGLECOIL (www.singlecoil.com)

Pre-tin the tip of your soldering iron and heat up the soldering spot while gently pulling on the wire until it comes out (Photo 5). This should not take longer than 2 to 3 seconds. A small chisel-shaped soldering tip is my weapon of choice. Warning: Don’t touch the bobbin of the pickup with the soldering iron—it will melt. Repeat this procedure with the second wire.

Courtesy of SINGLECOIL (www.singlecoil.com)

Strip the new wire, pre-tin it, pull it through the hole, and bend it so the stripped part will touch the soldering spot (Photo 6). I prefer to guide the wire with my hands, but you can also use tweezers for this. Now pre-tin the tip of your soldering iron and heat up the soldering spot while gently pushing the wire until it is in. This should not take longer than 2 to 3 seconds to perform. Repeat this procedure with the second wire. Cut off the excess wire with a small side cutter.

To check your work, measure the DCR of the pickup and compare it to the value you measured before. Small differences are okay and can be caused by the higher temperature directly after soldering to the pickup, or the new wires can be a different type and might have a different length. If you read zero or infinite, there is something wrong and you should check your soldering spots.

Courtesy of SINGLECOIL (www.singlecoil.com)

Take off the pickup cover you put on the pickup to protect the winding, and you are done (Photo 7). Congratulations! If you’re doing this regularly, you’ll become better and faster over time, so don’t worry if it takes longer than expected the first time.

Staggering pickup wires is a neat trick to not waste any wire, which can be a real issue when using expensive audiophile wires. Pickup manufacturers usually apply the same wire length to all pickups, no matter if it’s a bridge, middle, or neck pickup. And they’re usually way too long, resulting in a good portion of obsolete, snipped off wires. To avoid this, you can add only the length of new wire you really need. Here are the values I use in the shop for a standard Stratocaster:

That’s it for this month. Next, we’ll continue with our guitar relic’ing project, so stay tuned. Until then ... keep on modding!

Jackson Audio and Silvertone introduce an exact recreation of the legendary Twin Twelve amplifier in pedal form.

In 1963, history was made with the release of the Silvertone Twin Twelve Amplifier. Originally listed in the sears catalog as the 1484, the Twin Twelve was offered from 1963 to 1967 and became the most coveted of all the Silvertone amplifiers. The unique sound of this amplifier proudly powers the tones of many of today’s best rock icons such as Jack White, Dave Grohl, Beck, Billie Joe Armstrong (Green Day), Dan Auerbach (The Black Keys) and many more.

An exact recreation of the legendary Twin Twelve amplifier, the 1484 Twin Twelve Pedal can be used as a studio-grade preamp, booster, EQ or overdrive depending on how the controls are set.

MSRP: $249.00. For more information, please visit jackson.audio.

Gibson and Epiphone are proud to announce they have teamed with world renowned singer, songwriter and guitarist, Noel Gallagher to re-create his beloved 1960 Gibson ES-355 guitar and the Epiphone Riviera used during the mid-nineties.

​Gibson and Epiphone are proud to announce they have teamed with world-renowned singer, songwriter, and guitarist, Noel Gallagher to re-create his beloved 1960 Gibson ES-355 guitar and the Epiphone Riviera used during the mid-nineties.

“Fuck me, what a Guitar!” says Noel Gallagher of the 1960 Gibson ES-355. “I’ve actually sent my main one back to storage, something I haven’t done since the day I bought it… THAT’S how good it is!”

“This is THE guitar associated with Noel Gallagher since the late 1990s, we have taken our time over the details, we have worked closely with the artist and we have produced not only a truly remarkable recreation of the original but also a beautiful instrument which can be appreciated by all,” says Lee Bartram, EU Head of Marketing & Cultural Influence EMEA at Gibson Brands. “Gibson Custom continues to push the boundaries of what can be done with new guitar production, this project has been a labor of love for over 10 years and I’m extremely proud of what has been produced by amazing artisans in Nashville.”

​Since the late 1990’s the 1960 Gibson ES-355 has been Noel’s main live guitar and continues to grace stages around the world and be seen by millions of people. Gibson is proud to launch a limited run of 200 pieces of Noel’s main electric guitar which includes all the appointments which make the Gibson ES-355 the pinnacle of guitar craftsmanship, including a multi-ply bound maple body, a mahogany neck, and ebony fretboard, a Varitone switch, and a Bigsby B7 vibrato tailpiece. A reproduced handwritten lyric sheet, a hand-signed Certificate of Authenticity, and a custom Bear Strap exactly like Noel’s are also included.

MSPR: $9,999.00. For more information, please visit gibson.com.

This set of Heavy Core Strings was developed with great input from Head and Munky for increased dynamic range, optimal tension when drop-tined, and incredible tuning stability when playing hard on 7-string guitars.

Working closely with Head and Munky of nu-metal architects Korn, Dunlop crafted Heavy Core Korn Guitar Strings to unlock the true potential of their 7-string guitars. These strings feature increased dynamic range, optimal tension when drop-tuned, and incredible tuning stability.

Dunlop Heavy Core Korn Guitar Strings are available for $24.19 MSRP from your favorite retailers or directly online from jimdunlop.com.